You are currently not logged in.  Logon or register to access more features. Cross-Riders.com is a FREE service provided by Victory Riders Network.

Search:




2009 Vision Wiring Diagram needed - Instruments loose power
Jump to page : 1
Now viewing page 1 [25 messages per page]
View previous thread :: View next thread
   Discussion -> Victory General DiscussionMessage format
 
NCRYDER
Posted 2017-07-13 8:11 AM (#192094)
Subject: 2009 Vision Wiring Diagram needed - Instruments loose power


Puddle Jumper

Posts: 20
I am in search of a full wiring diagram for a 2009 Victory Vision. I have an intermittent problem where the instruments, radio, etc. loose power, but the bike will run and has headlights. I can't find a common cause, but I recently noticed that sometimes I can simply switch the bike off to the accessory position and back on, then the power returns to the instruments and radio, etc.
Top of the page Bottom of the page
11znl
Posted 2017-07-13 4:15 PM (#192095 - in reply to #192094)
Subject: Re: 2009 Vision Wiring Diagram needed - Instruments loose power


Puddle Jumper

Posts: 10
Edendale New Zealand
NCRYDER,

https://www.mediafire.com/folder/aoq581k2ab25z/Victory_Manuals

Try this link, I downloaded a service manual from here for my 2008 Vision. I cannot see one for a 2009 but I would imagine there would not be many changes between the two.

Rob
Top of the page Bottom of the page
willieh
Posted 2017-07-13 4:20 PM (#192096 - in reply to #192094)
Subject: Re: 2009 Vision Wiring Diagram needed - Instruments loose power


Puddle Jumper

Posts: 48
huntington In.
My bike does the same thing. Check the switch. If I wiggle the switch everything comes back on
Top of the page Bottom of the page
eotsis1
Posted 2017-07-13 8:49 PM (#192097 - in reply to #192094)
Subject: Re: 2009 Vision Wiring Diagram needed - Instruments loose power


Puddle Jumper

Posts: 35
, IL United States
mine does the same thing occasionally. Wiggle the key switch position does the trick. I suppose you could replace the switch.
Top of the page Bottom of the page
Bones
Posted 2017-07-13 11:47 PM (#192098 - in reply to #192094)
Subject: Re: 2009 Vision Wiring Diagram needed - Instruments loose power


Puddle Jumper

Posts: 43
Rossville, IL
Mine sometimes too, usually after coming out of winter storage. I can always tell as the key gets harder to pull out and it doesn't click through the detents when turning it on. I suspect it gets a little corrosion from water getting in it from either rain or washing it. I use my trusty Kano Kroil and stick the spray tube down in to the keyhole and give it a little squirt. Slide the key in and out and rotate it a few times and it's good to go for the season.
Top of the page Bottom of the page
NCRYDER
Posted 2017-07-21 9:47 AM (#192113 - in reply to #192094)
Subject: Re: 2009 Vision Wiring Diagram needed - Instruments loose power


Puddle Jumper

Posts: 20
Thanks for the responses, I will check my switch and the diagrams in the service manual.
Top of the page Bottom of the page
Arkainzeye
Posted 2017-07-25 2:32 PM (#192127 - in reply to #192094)
Subject: Re: 2009 Vision Wiring Diagram needed - Instruments loose power


Visionary

Posts: 3773
Pittsburgh, PA
I just read about someone with a 2012 ness vision that has the same problem . And when he wiggled his key it woukd work ... for him it was his ignition assembly ..
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [25 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

Copyright © 2007-2024 Victory Riders Network™